Weak airflow from every vent
We clean the evaporator coil and blower wheel, then test static pressure to confirm airflow is back in spec. Most Midvale homes feel the difference the same day.
HVAC Coil Cleaning Midvale UT restores the heat exchange your system needs to cool and heat efficiently. We pull the blower, inspect the evaporator and condenser coils, and clean them with professional-grade equipment. If your airflow feels weak, your energy bills climbed, or your system short-cycles, dirty coils are often the cause. We serve homeowners and businesses across Midvale, UT and Salt Lake County.

HVAC Coil Cleaning Midvale UT is a deep mechanical cleaning of the two coils that move heat in and out of your home: the evaporator coil inside the air handler and the condenser coil in the outdoor unit. Dust, pet hair, pollen, and biofilm build up on the fins and block airflow. We remove that buildup with coil-safe cleaners, low-pressure rinses, and soft brushes so the fins stay straight and the refrigerant can do its job. It is not a spray-and-go job; we pull panels, inspect the drain pan, and check the blower wheel while we are in there.
Midvale sits in the Salt Lake Valley, where winter inversions trap fine dust and summer temps push AC systems hard from June through September. That combination loads coils faster than most homeowners expect. If you have not had HVAC coil cleaning service Midvale UT in two or three years, your system is likely running 10 to 20 percent less efficient than it should. We also see condenser coil cleaning Midvale requests spike in late spring when homeowners test their AC for the first time and notice weak cooling.
Every coil cleaning visit covers the core work that restores airflow and efficiency. If we find something extra, like mold growth in ducts or a failing blower motor, we quote it before we touch it. Here is what you get as standard.
We apply coil-safe cleaner, let it dwell, and rinse with low pressure so the fins stay straight. A flexible duct rod and soft brush reach the back of the A-coil where dust hides. We flush the drain pan and check the condensate line.
Outside, we remove debris from the cabinet, comb straight any bent fins, and clean the coil from the inside out. We check the fan motor and capacitor while the unit is open, so you know if something is about to fail.
A dirty blower wheel throws off balance and cuts airflow. We inspect it on every visit and clean it when buildup is heavy. If it needs replacement, we tell you before we order parts.
Standing water in the drain pan grows mold and algae. We flush the pan and the condensate line to keep water moving. A clogged drain line is the number one cause of water damage from an AC system.
After cleaning, we measure the temperature difference between the return and supply air. A healthy system runs 16 to 22 degrees. If yours is off, we investigate before we leave.
You see exactly what we removed. We photograph the coils before and after cleaning and show you the difference on our tablet. No guessing whether the job was done.
We start by pulling the blower panel and the outdoor unit cover. Using a duct camera and a blower door test, we check static pressure, airflow, and visible buildup. You get a straight answer on whether the coil needs cleaning or replacement. This takes 15 to 20 minutes.
We apply a coil-safe foaming cleaner, let it dwell, then rinse with low pressure so the fins are not bent. A flexible duct rod and soft rotary brush reach the back side of the A-coil where dust hides. We flush the drain pan and check the condensate line while we are there. About 45 to 60 minutes.
Outside, we remove debris from the cabinet, straighten bent fins with a fin comb, and clean the coil from the inside out with a compressed air nozzle and coil cleaner. We check the fan motor and capacitor while the unit is open. Another 30 to 45 minutes.
A dirty blower wheel throws off balance and reduces airflow. We inspect it, clean it if needed, and check the duct insulation and register covers for gaps. If we spot mold growth in ducts or pest infestation in ducts, we flag it before we button everything up.
We run the system, measure the temperature split across the evaporator coil, and confirm the drain is flowing. Then we walk you through what we found, show you the before-and-after photos, and give you a filter schedule. Total job time is usually 2 to 3 hours.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Rotary brush system used to clean the back side of evaporator coils and blower wheels without bending fins or damaging the coil surface.
Captures fine dust and debris we dislodge during cleaning so it does not settle back into your ducts or your home's air.
Lets us see inside the air handler and duct runs to confirm where buildup is and verify the coil is clean when we finish.
Used on condenser coils to blow debris out from the inside, which is the only way to clean a coil properly without pushing dirt deeper.
Reaches into tight plenum spaces and around the A-coil where a brush alone cannot get. Common in older Midvale homes with tight mechanical closets.
Measures how leaky your duct system is. If ducts are leaking, clean coils will foul again quickly, so we check this before we finish.
A homeowner in Midvale Heights called in July because the AC was blowing warm air. The evaporator coil was frozen solid and the filter was completely clogged with dust and pet hair.
We thawed the coil, cleaned it with coil-safe cleaner, flushed the drain, and replaced the filter. The temperature split went from 8 degrees to 19 degrees, and the house hit 72 within two hours.
A rental property in Fort Union had a condenser coil packed with cottonwood fluff and grass clippings. The unit was short-cycling and the tenant reported high power bills.
We removed the debris, cleaned the coil from the inside out, and straightened bent fins. The system's amp draw dropped back into spec, and the tenant's next power bill was $34 lower.
A homeowner in Copperview noticed a musty smell every time the AC ran. The evaporator coil had visible mold growth and the drain pan was holding standing water.
We cleaned and treated the coil, flushed the drain pan and condensate line, and checked the ducts for moisture. The smell was gone the same day and has not returned.
Dirty coils do not just waste energy. They cause the breakdowns that leave you without heat or AC when you need it most. Here are the problems we fix most often in Midvale.
Ask a pro →We clean the evaporator coil and blower wheel, then test static pressure to confirm airflow is back in spec. Most Midvale homes feel the difference the same day.
We clean the condenser coil from the inside out, straighten bent fins, and verify the system is pulling the right amp draw. You get a measurable efficiency recovery.
We clean the coil, flush the drain pan and line, and treat the cabinet. If we find mold growth in ducts, we quote duct cleaning as the next step.
We thaw the coil, clean it, and check the refrigerant charge and filter. Nine times out of ten the freeze started with a dirty coil and a clogged filter.
Most residential coil cleaning jobs in Midvale run $250 to $550 in 2026, depending on how many coils need cleaning and how hard they are to access. A single evaporator coil cleaning is on the lower end. Cleaning both the evaporator and condenser coil, plus a blower wheel cleaning, pushes toward the higher end. We quote flat rates before we start.
Every 12 to 24 months for most Midvale homes. If you have pets, live near a dusty construction site, or run your AC hard from June through September, lean toward annual cleaning. Homes with a history of mold growth in ducts or pest infestation in ducts should be checked every year. We can set you up on a reminder schedule.
Our standard service includes evaporator coil cleaning, condenser coil cleaning, drain pan flush, condensate line check, blower wheel inspection, and a temperature-split test. We also check register covers and visible duct insulation. If we find mold growth in ducts or restricted airflow from duct debris, we will quote that separately before doing any extra work.
Yes. Dirty coils are one of the top causes of high energy bills and restricted airflow. After cleaning, most systems recover 10 to 15 percent of their cooling efficiency. That means shorter run times, lower summer power bills, and less strain on the compressor. We measure the temperature split before and after so you can see the difference.
Dirty coils cost you money every month. We clean them right, show you the proof, and get your system breathing easy again. Call (855) 927-7517 for a flat quote and same-day availability across Midvale.
Get a Free Quote (855) 927-7517 →Call (855) 927-7517 or email [email protected] and we will get you a flat quote, usually within the hour during business hours. We run same-day and next-day slots across Midvale and Salt Lake County. If you have an after-hours emergency, the phone line stays open.